#Zeilboot antenne kopen series#
You can do whatever you want with your data, like export the raw data to a time series database or use it with another automation engine. The product is designed as an open platform that puts you fully in control, without limitations. With Home Assistant Yellow, there is no vendor lock-in. If you require more power, the device can be turned into an 802.3at Type 3 Class 4 (PoE+, up to 25 W) device by changing a jumper. The Power-over-Ethernet variant of the Yellow Kit is by default configured as an 802.3at Type 1 Class 3 device (PoE, up to 15.4 W). Under load, this increases to about 5-9 W. Home Assistant Yellow uses about 1.5 W when idle, and 2.5 W if an NVMe SSD is installed. We opted for a barrel jack over USB because many USB power adapters do not supply enough power, which results in an unreliable system. Home Assistant Yellow is powered by a 12 VDC, 2 A power supply with a barrel jack. ESPHome is an open source project by the creators of the Home Assistant Yellow and has state-of-the-art integration with the Home Assistant software. It also allows you to extend and reconfigure your sensor node independently. Instead, we suggest using an external ESP-based microcontroller with ESPHome, which means you can place sensors and cameras anywhere, not just physically connected to Home Assistant. That said, we don’t recommend using the GPIO pins with Home Assistant at all. This header is compatible with the first ten pins of the standard 40-pin header, which makes it compatible with accessories that only use those first ten pins.
#Zeilboot antenne kopen serial#
Instead, there is a 10-pin header (labeled J11 in the image below) that exposes a serial port and I☬. This is why we don’t include a Raspberry Pi-compatible 40-pin header - most of those pins are already used. Most GPIO pins on Home Assistant Yellow are used for on-board features such as the Zigbee module, audio DAC and for the debug console.
The Raspberry Pi Compute Module 4 allows you to communicate with external components via GPIO pins. Note that we do not recommend connecting Home Assistant to your network over Wi-Fi because a reliable Internet connection is important for the backbone of your smart home.
#Zeilboot antenne kopen install#
Home Assistant Yellow does not have integrated Bluetooth or Wi-Fi, but you can easily install a variant of the Raspberry Pi Compute Module 4 that includes both. For example, each region of the world requires a different Z-Wave antenna and the regulatory approval for a board with one radio is much simpler than that with two.
There are several reasons we did not include Z-Wave on the mainboard itself. Home Assistant Yellow does not include a Z-Wave radio, but it is possible to use a Z-Wave USB stick or attach the AEOTEC Z-Pi 7 inside the case. Z-Wave is an alternative to Zigbee but is not compatible with Zigbee. The chip is Thread-certified and will support the upcoming Matter smart home standard. Home Assistant Yellow has an integrated Zigbee chip by Silicon Labs to control Zigbee-enabled devices in your home. Accommodates custom heat sink (included).Translucent injection-molded polycarbonate plastic.Ethernet: PoE+ IEEE 802.3at-2009 Class 3 or 4 (selectable via jumper).12 V / 2 A through barrel DC power jack (5.5 mm x 2.1 mm).Status LEDs (can be powered off during regular operation).USB mode: CM4 USB 2.0 interface for USB recovery.UART mode (default): debug USB-to-serial adapter.1 x USB-C 2.0 device port ( Silicon Labs CP2102N USBXpress USB bridge).Note: Google Coral AI Accelerator not working, details in this issue.Pre-installed with Zigbee 3.0 firmware (EZSP), can be upgraded.1024 KB flash program memory, 96 KB RAM data memory.2.4 GHz radio with TX power up to +20 dBm.Supports Zigbee 3.0, OpenThread, and Matter.Integrated smart-home wireless ( Silicon Labs MGM210P Mighty Gecko Module).Regulatory approval does not cover wireless variants.Quad-core Cortex-A72 (ARMv8) 64-bit / 1.5 GHz.Supports direct boot from NVMe devices (e.g., for CM4 Lite).Carrier board for Raspberry Pi Compute Module 4 (CM4).PACKAGES Ready to sail Mainsail cruising plus, Dacron 3-Radial cut, One Sails Genoa cruising plus, Dacron 3-Radial cut, 105%, UV protection, One Sails MDS Sliders for mainsail Lazy bag and lazy jack Genoa thru deck furler with deck equipment Anchor windlass 1000W-12V (incl. LOA: 11.60 m LWL: 10.01 m BEAM: 3.72 m DRAFT: 2.10 m DISPLACEMENT: 6200 kg HULL: Vacuum infusion vinylester epoxy based HULL COULOR: white COCKPIT: teak ENGINE: Yanmar 3YM30AE-C +SD20 (sail drive) 21,3kW FUEL TANK: 100 L WATER TANK: 180 L